新闻中心

  • 新闻中心
您现在的位置:主页 > 新闻中心 >

新闻中心

济南冲孔字制作方法及技巧大总结

页面更新时间:2015-08-17 11:30 来源:未知 作者:admin 点击:
济南冲孔字是采用发光二级管为光源制作的发光字体。led可以给国家和使用者节省大量电能,给承做方节省大量工时。LED应用技术的发展,给竞争激烈的广告业增添了新的活力。其独有的、不同的发光形势、被广泛的应用在广告产品的制作领域。不同规格的济南冲孔字 http://www.kangmingda.com/ 有着不同的发光角度和不同的亮度。半导体超高亮度发光二极管(LED),尤其是氮化物白光发光二极管,具有体积小、电压低、寿命长、响应快、无频闪、耗能少、发热少等优点,正逐渐成为新一代绿色、节能、环保、长寿命的照明光源。
 
Ji'nan piercing the word is the use of light-emitting diode light source for the two light source. LED can save a lot of power to the state and the user, to do a lot of work to do. With the development of LED application technology, it has added new vitality to the highly competitive advertising industry. Its unique, different luminous situation, is widely used in the production of advertising products. Different sizes of Ji'nan punching word have different light emitting angle and different brightness. Semiconductor high brightness light-emitting diode (LED), especially the nitride light emitting diode, has small volume, low voltage, long life, response the advantages of fast, no stroboscopic, less energy consumption, less heat, is gradually becoming a new generation of green, energy saving, environmental protection, long life lighting light source.
 
方法及步骤
 
Methods and procedures
 
1把所要的字样用复印纸描在密度板上,四边各留5cm,用手动雕刻机安上相应的直刀,沿字的外线开出模具(内部走里线,其它走外线)。模具开出后,用锉刀把模具挫平整。然后再用锉刀和砂纸把字的阴阳模各边及各角磨成圆弧状,一定要圆滑、均匀,最后用砂纸磨平。也可用电脑雕刻机刻模具,加够高度后高棱角处理圆滑即可。
 
1 to be the words with copy tracing paper in density board. Each of its four sides left 5cm, with manual engraving machine to install the corresponding straight knife, along the word outside the open mold (internal walking in line, the other to go outside. Die out, with a file to die down. And then rasp and sandpaper the words of yin and Yang in the mode of each edge and the angle grinding arc shape must be smooth, uniform, finally using sandpaper. Also available computer engraving machine engraving mold, plus a high degree of high angular processing smooth.
 
2底板的制作要求,底板的阳模四边要处理圆滑、四角要磨成圆弧度和倾斜度(即四角上窄下宽),以方便脱模。底板的阴模底部用砂纸磨一下即可,角度不要太大,这样可以缩小两块底板拼接时的缝隙。亚克力灯箱底板模具的计算方法亚克力灯箱底板模具的计算方法有两种情况,此两种算法针对于等份割成若干块的底板而言。
 
2 floor of the production requirements, the bottom sides of the mold to smooth processing, and the four corners to grinding arc and inclination (i.e. on the four corners of the narrow width), to facilitate the release. Bottom of the bottom of the female die with sandpaper grinding can be, angle should not be too high, so you can narrow the two floor mosaic of gap. Calculation method of acrylic light box bottom plate of the die of the calculation method of acrylic light box bottom plate of the die has two kinds of circumstances, the two kinds of method for equal parts cut into several blocks of floor.
 
3模具横向或竖向分割成若干块的算法如下:用总长度减掉底板两侧的留边尺寸等于剩下要制作模具的总长度.用剩下要制作模具的总长度除以等份分割块数等于要制作底板模具的尺寸用总宽度减掉底板两侧的留边尺寸等于要制作底板模具的寸把2算出的尺寸减掉5毫米,是两块底板拼接时缝隙的损耗(也就是拼接不严的损耗)最后总尺寸的长短,由成型后的多块亚克力底板拼接在一起后,在底板的两侧边上找。
 
3 Die horizontal or vertical split into several blocks of the algorithm are as follows: with total length of lose of both sides of the base plate of the left side size is equal to the left to make a mold of total length. With the remaining to make the mold total length divided by equal parts segmentation blocks is equal to the production of mold plate size with a total width of cut off both sides of the bottom plate of the left side dimension equal to to make the mold plate inch to calculate the 2 minus the size of the 5 mm, two floor mosaic gap loss (that is, the lax splicing loss) the total size of the length, by forming a plurality of acrylic floor splicing together, on both sides of the floor to find.
 
4先要有字面雕刻出来,绕着字面在铁皮上画出底壳剪出来,然后围好字边条,焊好字底壳,在底壳里排好led模组!!连接好出线!把围好的字面扣到底壳上,边带上钻孔拧螺丝
 
4 to literally carved out, around the literal in the metal, painted at the end of the shell cut out, then around good word edgings, welding good word at the end of the shell and in the bottom of the shell row LED module!! Connect the outlet! Put the enclosed in the shell, and the drill hole is screwed.
5每串灯的正极接线用一根红色长电线并联焊接,负极接线用一根黑色长电线并联焊接。把红色电线连接到led专用5v或12V电源的正极,黑色电线连接到led专用5v或12V电源的负极(正、负极不能接反)封胶把LED固定到铁皮上。测试老化:连好之后,打开电源。检查处理不亮的,然后进行老化测试24到48小时。
 
5each light cathode wiring with a long red wire parallel welding, the anode wire with a long black wire parallel welding. Connect the red wire to the LED 5V or 12V power supply, the black wire is connected to the 5V or 12V power supply of the negative (positive and negative LED) sealing glue to the LED. Test aging: connect well, turn on the power supply. Check the handle is not bright, and then carry out the aging test for 24 to 48 hours.