新闻中心

  • 新闻中心
您现在的位置:主页 > 新闻中心 >

新闻中心

教你济南冲孔字怎么打孔

页面更新时间:2015-07-02 10:11 来源:未知 作者:admin 点击:

一、济南冲孔字制作需要工具:30W或40W电烙铁,氩弧焊机,尖嘴钳,剪刀,剥线钳,曲线锯,电钻,胶枪,螺丝刀等,几乎和做电子灯箱一样.当然方法也是大同小异的。

Jinan punching word production need tools: 30W or 40W soldering iron, argon arc welding machine, needle nose pliers, scissors, pliers, curve saw, electric drill, glue gun, screwdriver, etc., and almost do electronic boxes like. Of course method is similar to the.

二、济南冲孔字制作需要材料:铁板一般采用08或是1.0的具体看字的大小和客户的要求,led灯(有灯串和灯组单色七彩等),玻璃胶,胶条,电阻,电线,焊锡,LED专用电源。

Making second, Jinan punching word need material: iron general by the 08 or 1.0 specific character size and customer requirements, LED lamp lights on and lights group monochrome colorful, glass glue, adhesive tape, resistance wire, solder, led special power supply.

三、济南冲孔字制作:在铁皮板上锯下字的轮廓,当然你要先写一个字模.固定到合适的位置,薄的铁皮可以用铁皮剪,要好看或是厚的就用雕刻机,还有等离子切割、激光切割、线切割等。用电钻钻孔:5MM或9MM七彩灯一般12MM,也可以用冲孔设备直接冲好,方便快速。市场上也有冲孔板卖,间距根据外招牌制作安装的高度和制作成本而定的,一般LED中心间距为:10—30MM,间距越小,效果越好,成本越高。

Third, led exposed light-emitting word Jinan punching word production: saw the outline of the word in the tin plate, of course, you have to write a font. Fixed to the appropriate position, the thin iron sheets can be used iron scissors, to look good or thick with engraving machine, and plasma cutting, laser cutting, wire cutting, such as. Using electric drill: 5MM or 9MM colorful lamps for general 12MM, can also be used directly punching punching equipment, convenient and quick. On the market also has a perforated plate sell, spacing to make installation height and production cost according to the signs, the general led center to center spacing: 10 - 30mm spacing is smaller, the better, the higher the cost.

济南冲孔字 http://www.kangmingda.com/ 应用多的原因:

Reasons for the application of more than Ji'nan punching:

原因一:防水,节能、安全:众如周知,济南冲孔字的功率小,耗电量低。由于输出电压低,因而更加安全。由于我们应用的济南冲孔字光源是防水的,因此,在下雨等天气里可正常使用,而不用去担心会烧坏。 虽然说LED灯是很少会坏的,但是如果遇到线的接触不良或者特殊情况坏了,需要去维修,这种LED外露字只需要高空吊人到广告牌坏的位置将坏的灯从正面拉出换完即可。

One reason: waterproof, such as: public security, information, power Ji'nan punching word of small, low power consumption. Because the output voltage is low, so it is more secure. Because we apply the Jinan punching word light source is waterproof. Therefore, in the rain and other weather can normal use, and no need to worry will burn. Although the LED lamp is rarely a bad, but if you encounter a line contact undesirable or special situation bad and need to repair, the LED exposed words only needs high hanging to billboard bad position would be bad for the light from the front out of the change can be finished.

原因二:不受大小的限制:一般来讲,LED吸塑等内发光字多受吸塑机等限制,大字很多需要去拼接,这样有损字的美观,外露字大字一般通过等离子切割弯折而成,因而不受机器而限制大小。不拼接,更美观。不受字的颜色的限制:一般内发光字受有机板的限制,如红色吸塑字,一般里面放的也是红色光源,发出来的也是红光,而外露发光字则不然,你可以将字烤成各种颜色的漆,晚上你需要亮什么颜色的灯就亮什么色的灯,一点不受底字的影响,而且大字由于离地面高,白天,LED外露的灯也不明显。

Two reasons: not subject to size constraints: Generally speaking, such plastic luminous characters by blister machine restrictions. Characters many need to splice, so loss of beautiful, exposed words characters generally by plasma cutting bending into, and thus not subject to machine the size limit. Not mosaic, more beautiful. From the limits of the color of the word: General luminous characters is limited by the organic plate, such as red plastic, generally placed inside and red light source, sends out is red and exposed luminous characters, otherwise, you can roast words into various colors of paint, night you need what color lights lit what color lamp, from word base effect and characters due to high off the ground. During the day, LED exposure lamp is not obvious.